CHANNEL WHEEL
罐道輪為一種立井提升容器用华体会体育中心
其結構由底座、擺轉臂、滾輪、緩衝器組成;华体会体育中心
結合我國礦山特點為目前運行中的
提升容器更換新型滾輪導向裝置提供了便利條件,
廣泛應用與礦山,煤炭等工業生產部門。
礦山
MINE
煤炭
COAL
工業生產
INDUSTRIAL PRODUCTION
华体会体育中心
沿罐道運行時,因罐道的設計安裝,會產生接點、彎曲高點,輪頭會受到水平推力作用,由於支臂架、
底座和緩衝器之間的鉸接作用,使緩衝器受壓縮產生反彈力。
緩衝器的反彈力
一、保證提升容器順利通過高點;
二、保證提升容器不得與罐道發生碰撞;
三、要保證提升容器在上升和下降過程中擺動幅度不得太大。
1、Ensure THAT THE LIFTING VESSELPASSES THROUGH THE HIGH POINT SMOOTHLY;
2、ENSURE THAT THE LIFTING CONTAINER DOES NOT COLLIDE WITH THE TANK CHANNEL;
3、IT IS necessary TO ensure THAT THE SWING RANGE OF THE ILFTING CONTAINER IN THE PROCESS OF RISING AND FALLING IS NOT TOO LARGE.
所以緩衝器的緩衝性能是嚴格按提升容器的重
量、運行速度進行設計的,但其輪頭最大水平
推力一定要小於或等於行業標準的要求。根據
以上理論設計製造出的华体会体育中心
能夠有效滿足
用戶要求。
罐道輪 型號參數
罐道輪的作用原理是滾輪受力通過支架、調節套、調節螺杆、碟簧軸施力於碟簧上,通過碟簧軸
上、下運動釋放和壓縮碟黃組實現緩衝。
The working principle of the channel wheel is that the roller is forced on the disc spring through
the bracket, the adjusting sleeve,
the adjusting screw and the disc spring shaft, and the buffer is realized by the up and down
movement of the disc spring shaft and
the compression of the disc yellow group.
型號 | 滾輪直徑mm | 最大水平力KN | 緩衝行程mm | ||
---|---|---|---|---|---|
單輪 | L25 | 250 | 12 | 10~14 | |
L30 | 300 | 16 | |||
L35 | 350 | 24 | |||
L42.5 | 425 | 33 | |||
L45 | 450 | 35 | |||
L50 | 500 | 36 | |||
雙輪 | LS30 | 300 | 20 | ||
LS35 | 350 | 28 | |||
LS42.5 | 425 | 42 | |||
LS45 | 450 | 44 | |||
LS50 | 500 | 45 |
選擇我們的優勢
罐道輪的作用原理是滾輪受力通過支架、調節套、調節螺杆、碟簧軸施力於碟簧上,通過碟簧軸上、
下運動釋放和壓縮碟黃組實現緩衝。
The working principle of the channel wheel is that the roller is forced on the disc spring through
the bracket, the adjusting sleeve, the ad
justing screw and the disc spring shaft, and the buffer is realized by the up and down movement of
the disc spring shaft and the compres
sion of the disc yellow group.
STRONG IMPACT
RESISTANCE
NO.1
抗衝擊性強
承載能力大、壽命長、調整維修方便;
底座等零部件采用新型材料,整體結構強度更
高抗衝擊性強。
STADBLE OPERATION AND
MAINTENANCE FREE
NO.2
運行穩定、免維護
緩衝器複位壓力小,可有效地避免滾輪與罐道
產生異常碰撞。通過杠杆傳遞 到減震筒上,同
時起到導向、緩衝與穩定作用。
LOW WEAR AND LONG
SERVICE LOFE
NO.3
磨損度低、使用壽命長
罐道與罐耳由滑動摩擦變為滾動摩擦,因此減
少了動力消耗,降低了噪音,罐道和罐耳的磨
損也大大降低。從而,提高了罐道和罐耳的使
用壽命。
故障分析及排除
滾輪端蓋中心孔上安裝有密封塞,同時端蓋上設有通氣孔,真正做到新油易入,
舊油易出。
The center hole of the roller end cover is provided with a sealing plug, and the end cover is
provided with an air vent, so that
the new oil is easy to enter and the old oil is easy to exit.
原因分析: 滾輪與罐道接觸過緊
排除方法:缺少潤滑脂調整滾輪接觸到
罐道即可,不要加預緊力
1、原因分析: 擺架下鉸鏈套磨損,間隙大
排除方法:更換新套及鉸鏈軸
2、原因分析: 軸承遊隙太大
排除方法:拆下副輪轂,用圓螺母調整
軸承遊隙
原因分析: 軸承缺少潤滑脂
排除方法:注入適量潤滑脂